jkings

BLOGS

How to Cut Rebar with an Angle Grinder: Disc Choice and Technique

Oct 05,2026

Bill Saint-Gobain

The fastest way to cut rebar on site is an angle grinder with the right disc. Which disc, what thickness, and the technique for clean, fast rebar cuts.
图片名称

How to Cut Rebar with an Angle Grinder: Disc Choice and Technique

Rebar is everywhere on a construction site — and it always needs cutting to length. While dedicated rebar cutters exist, the angle grinder with a cutting disc remains the most common, cheapest, and most versatile way to do it. Done right, a grinder cuts #5 rebar in seconds. Done wrong, it eats discs and leaves dangerous, burred ends. Here is the complete approach.

The Right Disc for Rebar

Rebar is plain carbon steel, so a standard aluminum oxide metal cutting disc is the correct and economical choice. The decisions that matter are diameter and thickness:

  • Diameter: a 115 mm (4.5") or 125 mm (5") disc handles rebar up to about 25 mm in one pass from two sides. For bunded bars or heavy #8+ rebar, a 230 mm (9") grinder cuts faster with fewer disc changes.
  • Thickness: 1.0–1.6 mm thin discs cut rebar fastest with the least effort and leave small burrs. On rough site work where discs get knocked and twisted, 1.6–2.0 mm survives better. For volume cutting on a 355 mm chop saw, use 2.5–3.2 mm.
  • Quality tier: rebar is abrasive and hard on discs. A mid-grade or premium disc typically delivers 30–60% more cuts per disc on rebar than the cheapest economy disc — worth it when cutting hundreds of bars a day.

Setup: Half the Job Is Before the Cut

Support the bar on both sides of the cut line. This is the single most important step. Rebar that sags as it is nearly severed will pinch the disc — the classic cause of shattered discs and kickback on site. Lay the bar across two supports with the cut point between them and the offcut free to fall away, opening the kerf rather than closing it.

Mark and bundle smart. A soapstone mark keeps cuts square. When cutting multiple bars, tape them into a tight bundle and cut through the bundle — one pass cuts several bars and the bundle supports itself.

Cutting Technique

  1. Fit the guard, wear eye protection, gloves and hearing protection — rebar cutting throws a dense spark stream.
  2. Let the grinder reach full speed before touching the bar.
  3. Start the cut on the top of the bar with light pressure to establish a straight kerf, then feed steadily downward. Do not saw back and forth — keep the disc moving in one straight plane.
  4. Let the disc's weight and speed do the work. If the grinder bogs down, you are pushing too hard.
  5. For bar thicker than the disc's cutting depth, cut halfway through, rotate the bar 180 degrees, and complete the cut from the other side — the kerfs will meet.
  6. As the cut nears completion, ease off pressure so the disc exits cleanly instead of grabbing the last sliver of steel.

After the Cut: Deburring and Safety

A thin disc leaves a small burr; knock it off with the edge of a grinding disc or a few strokes of a flap disc if the end will be handled or tied. Freshly cut rebar ends are razor sharp and hot — handle with gloves. If the cut end goes into concrete, no finishing is needed at all.

Productivity Tips for Volume Work

  • For more than ~50 cuts of the same size, a 355 mm chop saw pays for itself in speed and disc economy.
  • Cut bundles, not single bars, whenever lengths match.
  • Track cuts per disc: on #4–#5 rebar a quality 125 mm disc should deliver roughly 80–150 cuts. Far fewer means wrong technique, wrong disc, or both.
  • Keep discs dry and flat in the site container — site moisture ruins discs faster than cutting does.

Frequently Asked Questions

What is the best disc for cutting rebar?

A 1.0–1.6 mm aluminum oxide metal cutting disc, 115–125 mm for single bars up to 25 mm. For bundles and heavy bar, a 230 mm grinder or 355 mm chop saw with a 2.5–3.2 mm disc.

Can I cut rebar with a diamond blade?

Abrasive discs are better and cheaper for standalone rebar. Diamond blades earn their keep when rebar is embedded in concrete — a diamond blade cuts both in one pass.

Why does my disc keep getting pinched when cutting rebar?

The bar is sagging and closing the kerf. Support both sides of the cut line and let the offcut fall away freely.


Related Topics

RELATED NEWS


Sharpen or Replace? How to Judge a Worn Saw Blade and What It Is Worth

A quality TCT blade can be sharpened 3-5 times — a cheap one often cannot. The signs of a dull blade, sharpening economics, and when to bin it.


How to Cut Laminate Flooring Without Chipping: Saws, Blades and Technique

Laminate chips and dulls blades like few materials. The right blade for each saw, which face to cut from, and how to keep edges factory-clean.


How to Cut Acrylic (Plexiglass) with a Circular Saw Without Cracking or Melting

Acrylic cracks from vibration and melts from heat. The right blade, speed and support for clean, crack-free circular saw cuts in plexiglass sheet.


How to Clean a Saw Blade: Removing Pitch and Resin Buildup

A dirty blade cuts like a dull one — burning, straining, tearing. How to clean pitch and resin off saw blades safely, and when cleaning is not enough.


Choosing a Miter Saw Blade for Trim and Fine Finish Work

Trim carpentry lives or dies on the miter cut. Tooth count, grind, hook angle and blade quality for glass-smooth cuts in molding, casing and trim.


Metal Cutting Saw Blade (Cold Saw): Low-Spark Cutting for Steel & Stainless

Metal cutting saw blades (MTCG) for cold saws cut steel and stainless with low spark, no dust and cool burr-free edges. Sizes 136–455mm, tooth guide.

%{tishi_zhanwei}%

Messages

图片名称

If you are interested in our products, please leave us a message and we will reply as soon as possible!

%{tishi_zhanwei}%